features standard part frequency range (80mhz ?2.0ghz) low passband ripple linear phase high selectivity applications cellular phone: e-amps, pcs and gsm, pdc cordless phone: ct-1, ism, dect land mobile radio (lmr) 915 mhz ism pager rke gps saf c 860.5m a* 7* 0* n tc designates c ?surface mount center alpha numeric numeric substrate: 180mm dia reels: saw filters multi-layered ceramic frequency character for package performance t ?lithium tc = 500/reel u surface mount in mhz design style code tantalate tc11 = 1,000/reel single layer ceramic characteristics code n lithium tc12 = 2,000/reel niobate 330mm dia reels: x ?crystal tc00 = 10,000/reel s ?sapphire tc05 = 5,000/reel tc04 = 4,000/reel tc02 = 2,000/reel *consult microwave group for details by part number. part numbering system typical cellular system and saw possibilities saw rx filter saw local filter saw if filter saw tx filter mixer mixer lna ant duplexer p.a. af if tcxo p.s. pll lpf vco 90mhz pll attenuation vs. frequency ?general comparison of filter characteristics attenuation frequency saw lc dielectric ceramic microwave filters saw filters 346 cg01-j saf series
center i.l. bandwidth attenuation ripple max. input/output pkg. tape app. part number function freq. (db) (mhz) (db) (db) vswr gdt impedance style code (mhz) max.* max. ( s) 824 to 849 3.8 tc00, safc836.5mc90t rf (tx) 836.5 3.8 869 to 894 25 1.8 2 n/s 50 ohm // 0pf sc33 tc05, 920 to 2000 32 tc11,tc12 869 to 894 3.5 tc00, safc881.5mc90t rf (rx) 881.5 3.5 824 to 849 30 1.5 2.0 50 ohm // 0pf sc33 tc05, 1100 to 2000 32 tc11,tc12 869 to 894 2.5 tc00, safc881.5md90t rf (rx) 881.5 2.5 824 to 849 20 1.5 2.5 50 ohm // 0pf sc33 tc05, 1100 to 2000 2.3 tc11,tc12 869 to 894 3.5 tc00, e-amps safc881.5mwc90t rf (rx) 881.5 3.5 824 to 849 30 1.5 2.0 50 ohm // 0pf sc33 tc05, /adc differential 1100 to 2000 28 tc11,tc12 fo 15khz 3.0 safc83.160ma40x 1st if 83.160 5.0 83.04 to 83.10 20 min. 1.5 n/s 10.0 850 ohm // 2.0pf sc511 tc, 83.22 to 83.28 20 min. tc11 fo 15khz 3.0 safc83.160mc40x 1st if 83.160 5.0 83.04 to 83.10 20 min. 1.5 n/s 8.0 850 ohm // 2.0pf sc511 tc, 83.22 to 83.28 20 min. tc11 fo 13khz 3 tc, safc85.380me35x 1st if 85.38 5.5 85.26 to 85.32 25 1.5 n/s 10 870 ohm // 1.7pf sc59 tc11, 85.44 to 85.50 25 tc04 fo 630khz 3 tc, safc130.4msc10t 1st if 130.38 5.5 135.33 40 n/s n/s 0.8 435 ohm // 0.8uh sc57 tc11, 139.65 to 140.91 45 tc04 1930 to 1990 4.5 sc33 tc00, safc1960ml1c0t rf (rx) 1960 4.5 1850 to 1910 15 3.0 2.5 50 ohm // 0pf low tc05, 1719 to 1780 23 profile tc12 1850 to 1910 4.5 sc33 tc00, safc1880ml1c0t rf (tx) 1880 4.5 1930 to 1990 9 3.0 2.5 50 ohm // 0pf low tc05, 3860 to 3980 14 profile tc12 1850 to 1885 2.8 pcs 1867.5 2.8 1930 to 1965 30 rf 3700 to 3770 20 sc44 tc, safc 1867.5t1897.5ml80t split 1885 to 1910 2.8 1.8 1.8 50 ohm // 0pf dual tc04 tx 1897.5 2.8 1965 to 1990 30 type tc11 3770 to 3820 20 209.75 to 211.01 5.0 safc210.38mwjsox if 210.38 8.5 130 to 209.13 33 1.0 in 775 ohm // 68nh sc513 tc02, differential 211.63 to 270 33 out 465 ohm // 54nh tc11 tc00, safc902.5ma90n rf (tx) 902.5 4 890 to 915 4 1.7 2.5 n/s 50 ohm // 0pf sc33 tc05 935 to 960 20 tc11, tc12 890 to 915 3.5 tc00, safc902.5mc90t rf (tx) 902.5 3.5 935 to 960 25 1.5 2.1 n/s 50 ohm // 0pf sc33 tc05, 1500 to 2000 40 tc11, tc12 890 to 915 3.5 tc00, safc902.5mwc90t rf (tx) 902.5 3.5 935 to 960 25 1.5 2.3 50 ohm // 0pf sc33 tc05, gsm differential 1500 to 2000 25 tc11, tc12 935 to 960 3.5 tc00, safc947.5mc90t rf (tx) 947.5 3.5 890 to 915 35 1.5 2.3 n/s 50 ohm // 0pf sc33 tc05, 1500 to 2000 40 tc11, tc12 935 to 960 3 tc00, safc947.5md90t rf (tx) 947.5 3.5 890 to 915 20 1.5 2.2 50 ohm // 0pf sc33 tc05, 1500 to 2000 23 tc11, tc12 935 to 960 3.8 tc00, safc947.5mwc90t rf (tx) 947.5 3.8 890 to 915 35 1.5 2.3 50 ohm // 0pf sc33 tc05, differential 1200 to 1500 35 tc11, tc12 925 to 960 3.0 sc33 tc00, safc942.5md1c0t rf (rx) 942.5 3.0 880 to 905 18 1.7 2.8 50 ohm // 0pf low tc05, 1850 to 2500 30 profile tc12 egsm 925 to 960 4.3 sc33 tc00, safc942.5myj1c0t rf (rx) 942.5 4.3 980 to 1100 23 2.2 2.8 50 ohm // 0pf low tc05, 1600 to 2500 25 profile tc12 1805 to 1880 4.5 sc33 tc00, safc1842.5ml1c0t rf (rx) 1842.5 4.5 1600 to 1710 35 3.0 2.5 50 ohm // 0pf low tc05, 1980 to 3000 20 profile tc12 rf (rx) 925 to 960 3.7 sc44 tc, egsm 942.5 3.7 880 to 905 15 2.5 2.7 50 ohm // 0pf dual tc04, gsm safc 942.5t1842.5ml80t 1600 to 2000 25 type tc11 1800 rf (rx) 1805 to 1880 4.2 sc44 tc, gsm1800 1842.5 4.2 1705 to 1785 7 2.5 2.7 50 ohm // 0pf dual tc04, 2800 to 4000 15 type tc11 fo 80khz 3 tc, safc246.000mc30x 1st if 246 5 245.6 and 246.4 25 1.0 n/s 2.5 420 ohm // 3.6pf sc59 tc04, 243 and 249 40 tc11 n/s: not specified. tape codes and package quantities defined at the end of the saw section of this catalog. *il for if filters is guaranteed at center frequency relative to 0db reference. i.l. for rf filters is guaranted across the pas s band relative to 0db reference level. **attenuation for if filters is relative to center frequency loss. attenuation for rf filters is relative to 0db reference leve l. cg01-j 347 ceramic microwave filters saw filters specifications saf series ceramic microwave filters
center i.l. bandwidth attenuation ripple max. input/output pkg. tape type part number function freq. (db) (mhz) (db) (db) vswr gdt impedance style code (mhz) max.* max. ( s) tx 902 to 904 4.5 tc00, safc903mf90t or rx 903 4.5 926 to 928 35 1.5 50 ohm // 0pf sc33 tc05, 944 to 948 40 tc11, tc12 tx 926 to 928 4.5 tc00, ism safc927mf90t or rx 927 4.5 902 to 904 35 1.5 50 ohm // 0pf sc33 tc05, 915 968 to 972 40 tc11, tc12 902 to 928 4.5 max. tc00, safc915ma70n rf 915.0 4.5 790 to 860 30 min. 2.0 2.5 n/s 50 ohm // 0pf sc44 tc04, 970 to 1040 20 min. tc11 fo 576mhz 3.0 tc, dect safu110.6msa40t 1st if 110.592 4.5 fo 1.15mhz 10 min. n/s n/s 0.7 300 ohm 1.2 h su511 fo 1.728mhz 30 min. tc11 806 to 825 4.0 max. tc, safc815.5ma70n rf 815.5 4.0 761 to 780 20 min. 2.0 2.5 n/s 50 ohm // 0pf sc44 tc04, lmr 851 to 870 20 min. tc11 851 to 870 4.0 max. tc, safc860.5ma70n rf 860.5 4.0 806 to 825 20 min. 2.0 2.5 n/s 50 ohm // 0pf sc44 tc04, 896 to 915 15 min. tc11 314.7 to 315.3 3.0 tc, safc315mf70t rf (rx) 315 3.0 293 to 293.9 50 1.5 2.0 50 ohm // 0pf sc44 tc04, 357.5 to 358.7 50 tc11 868 to 870 4.5 tc, safc869mf70t rf (rx) 869 4.5 825 to 828 40 1.5 50 ohm // 0pf sc44 tc04, rke 910 to 913 40 tc11 863 to 865 4.5 tc, safc864mf70t rf (rx) 864 4.5 820 to 823 40 1.5 50 ohm // 0pf sc44 tc04, 905 to 908 40 tc11 433.05 to 434.7 4.5 tc, safc434mc70t rf (rx) 433.9 4.5 389 to 392 50 1.5 2.0 50 ohm // 0pf sc44 tc04, 475.5 to 478.5 50 tc11 1574 to 1577 2.8 sc33 tc00, safc1575mb1c0s rf (rx) 1575.5 2.8 1382 to 1397 35 1.3 3.0 n/s 50 ohm // 0pf low tc05, gps 1478 to 1487 25 profile tc12 90 1mhz 3.0 tc, safc90ma31n if 90 6.5 84 to 85 25 2.0 0.5 365 ohm // 0.7pf sc59 tc04, 95 to 96 25 tc11 rf (tx) 940 to 960 4 tc00, safc950mb90n 950 4 810 to 830 45 2 n/s 2.5 50 ohm // 0pf sc33 tc05, 800 1050 to 2000 35 tc11, tc12 940 to 960 3.5 tc00, safc950mc90t rf (tx) 950 3.5 810 to 830 48 1.5 2.5 50 ohm // 0pf sc33 tc05, pdc 1050 to 2000 35 tc11, tc12 800 810 to 830 2.5 tc00 safc820me90n rf (rx) 820 2.5 940 to 960 32 1.5 n/s 2.5 50 ohm // 0pf sc33 tc05 800 1100 to 2000 22 tc11. tc12 810 to 830 2.2 tc00, safc820md90t rf (rx) 820 2.2 940 to 960 30 1.3 2.5 50 ohm // 0pf sc33 tc05, 1100 to 2000 22 tc11, tc12 1429 to 1453 2.7 tc00, safs1441mc1b0t rf (tx) 1441 2.7 1477 to 1501 15 1.5 2.3 50 ohm // 0pf sc22 tc05, 1783 to 1808 32 tc12 1477 to 1501 2 tc00, pdc safc1489mc90s rf (rx) 1489 2 1429 to 1453 15 1.2 n/s 2.7 50 ohm // 0pf sc33 tc05, 1.5 1737 to 1761 35 tc11, tc12 1477 to 1501 2.7 tc00, safc1489mc1b0t rx 1489 2.7 1429 to 1453 15 1.5 2.3 50 ohm // 0pf ss22 tc05, 1735 to 1766 35 tc12 893 to 898 4.0 rf (tx) 895.5 4.0 810 to 830 22 2.1 2.5 50 ohm // 0pf 895.5 1778 to 1796 20 sc33 tc00, safc 895.5t942.5mf1d0t 925 to 960 3.5 dual tc05, rf(tx) 942.5 3.5 870 to 885 18 2.3 3.2 50 ohm // 0pf type tc12 pdc 942.5 1850 to 1920 10 multi- 810 to 843 2.7 band rf (tx) 826.5 2.7 893 to 960 24 1.6 2.6 50 ohm // 0pf 826.5 1300 to 2000 12 sc33 tc00, safc 826.5t877.5mf1d0t 870 to 885 2.7 dual tc05, rf (tx) 877.5 2.7 925 to 960 26 1.3 2.6 50 ohm // 0pf type tc12 877.5 1300 to 2000 23 130 16khz 3.0 pdc safc130.000ma1g0x if 130.0 5.5 130 100khz 22 0.5 5 740 ohm // 1.1pf sc36 tc05, all 130 200khz 40 tc11 n/s: not specified. tape codes and package quantities defined at the end of the saw section of this catalog. *il for if filters is guaranteed at center frequency relative to 0db reference. i.l. for rf filters is guaranted across the pas s band relative to 0db reference level. **attenuation for if filters is relative to center frequency loss. attenuation for rf filters is relative to 0db reference leve l. 348 cg01-j ceramic microwave filters saw filters specifications saf series
center i.l. bandwidth attenuation ripple max. input/output pkg. tape type part number function freq. (db) (mhz) (db) (db) vswr gdt impedance style code (mhz) max.* max. ( s) 887 to 925 4.5 tc00, safc906ml90t rf (tx) 906 4.5 832 to 870 30 2.8 2.8 50 ohm // 0pf sc33 tc05, japan 2661 to 2775 20 tc11, tc12 cdma 832 to 870 4.5 tc00, safc851ml90t rf (rx) 851 4.5 887 to 925 22 3.0 2.8 50 ohm // 0pf sc33 tc05, 1000 to 2000 20 tc11, tc12 1750 to 1780 3.5 tc00, safc1765mf90t rf (tx) 1765 3.5 1840 to 1870 30 2.0 2.4 50 ohm // 0pf sc33 tc05, korea 3500 to 3560 25 tc11, tc12 pcs 1840 to 1870 3.5 tc00, safc1855mf90t rf (rx) 1885 3.5 1750 to 1780 23 2.0 2.4 50 ohm // 0pf sc33 tc05, 2300 to 4000 20 tc11, tc12 safc886me70t rf 886.0 3.5 884 to 888 3.5 max. 1.5 n/s n/s 50 ohm // 10nh sc44 tc, tc04, 840 to 846 40 min. tc11 safc931me70t rf 931.0 3.5 929 to 933 3.5 max. 1.5 n/s n/s 50 ohm // 10nh sc44 tc, tc04, 884 to 891 40 min. tc11 ct-1 913 to 915 3.5 max. tc, safc914me70t rf 914.0 3.5 891 to 894 30 min. 1.5 n/s n/s 50 ohm // 10nh sc44 tc04, 934 to 937 15 min. tc11 958 to 960 3.5 max. tc, safc959me70t rf 959.0 3.5 936 to 939 30 min. 1.5 n/s n/s 50 ohm // 10nh sc44 tc04, 979 to 982 20 min. tc11 1574 to 1577 2.8 sc33 tc00, safc139mc70n rf (rx) 1575.5 2.8 1382 to 1397 35 1.3 3.0 n/s 50 ohm // 0pf low tc05, 1478 to 1487 25 profile tc12 90 1mhz 3.0 tc, safc146mc70n if 90 6.5 84 to 85 25 2.0 0.5 365 ohm // 0.7pf sc59 tc04, 95 to 96 25 tc11 rf (tx) 940 to 960 45 safc154mc70n 950 4 810 to 830 45 2 n/s 2.5 50 ohm // 0pf sc33 tc12 800 1050 to 2000 35 940 to 960 3.5 tc00, safc162mc70n rf (tx) 950 3.5 810 to 830 48 1.5 2.5 50 ohm // 0pf sc33 tc05, pager 1050 to 2000 35 tc11, tc12 810 to 830 2.5 safc171mc70n rf (rx) 820 2.5 940 to 960 32 1.5 n/s 2.5 50 ohm // 0pf sc33 tc12 800 1100 to 2000 22 275 to 285 4.5 max. tc, tc04 safc280me70n rf 280.0 4.5 180 to 242.5 48 min. 2.0 n/s n/s 230 ohm // .2pf sc44 tc11 317.5 to 380 40 min. 276 to 286 4.5 max. tc, tc04 safc281me70n rf 281.0 4.5 181 to 243.5 48 min. 2.0 n/s n/s 230 ohm // .2pf sc44 tc11 318.5 to 381 40 min. 280 to 288 4.5 max. tc, tc04 safc284me75n rf 284.0 4.5 184 to 246.5 48 min. 2.0 n/s n/s 230 ohm // .2pf sc44 tc11 321.5 to 384 40 min. 928.8 to 932.2 4.5 max. tc, tc04 safc930.5me70t rf 930.5 4.5 884.8 to 890.2 45 min. 2.0 n/s n/s 50 ohm // 10nh sc44 tc11 906.8 to 911.2 30 min. n/s: not specified. tape codes and package quantities defined at the end of the saw section of this catalog. *il for if filters is guaranteed at center frequency relative to 0db reference. i.l. for rf filters is guaranted across the pas s band relative to 0db reference level. **attenuation for if filters is relative to center frequency loss. attenuation for rf filters is relative to 0db reference leve l. cg01-j 349 ceramic microwave filters saw filters specifications saf series ceramic microwave filters
ceramic microwave filters saw filters environmental specifications test item package test conditions test method filter is soldered onto the center of pcb which is laid on two small supporters smd spaced 90mm apart. the pcb is deflected to 1mm below the horizontal level by the pressing stick for 1 second and repeated 5 times. terminal strength a force of 1.0 kg shall be applied to each terminal in the direction of the axis of terminal for 30 5 seconds. leaded a force of 250 gf is applied to each lead in axial direction. the lead shall be bent 90 degrees to one direction, then in opposite direction and returned to the original position. solderability both lead terminals are immersed in methanol with 7 to 10% of rosin flux for about mil-std-202e 5 seconds, then immersed in soldering bath at 230 5? for 5 0.5 seconds. method 208c random drop both drop 3 times on concrete floor from 1.0 meter, (30cm for some products). vibration both vibration amplitude of 1.5mm at 10-55hz in each of three mutually mil-std-201e perpendicular directions for 1 hour. method 201a mechanical environmental test item package test conditions test method salt spray both hold in chamber with 5% salt density at 35? +1.1??.7? for 48 hours. mil-std-202e measure after exposure to room condition for 1 hour. method 101d temperature cycling both exposure to 5 cycles of ?5? (30 minutes) +25? (15 minutes), ?5? mil-std-202e (30 minutes) +25? (15 minutes). test after 2 hours exposure to room conditions. method 102a humidity both hold in chamber with 90 to 95% r.h. at 40 2? for 100 hours. test after 2 mil-std-202e hours exposure to room conditions. method 103b operating humidity both hold in chamber with 90 to 95% r.h. at 40 2? for 100 hours at 6vdc. mil-std-202e test after 2 hours exposure to room conditions. thermal shock both expose to 5 cycles of ?5? (30 minutes) +85? (30 minutes). test after 2 hours mil-std-202e exposure to room conditions. method 107d life test (high) both hold in chamber at 85 2? for 100 hours. test after exposure to room mil-std-202e conditions for 2 hours. method 108a life test (low) both hold in chamber at ?0 2? for 100 hours. test after exposure to room mil-std-202e conditions for 2 hours. method 108a operating life test both hold in chamber at 85 2? for 100 hours at 6vdc. test after exposure to room conditions for 2 hours. sulfuration both hold in chamber with 1000ppm sulfur density for 24 hours. test after exposure to room conditions for 2 hours. filter shall be preheated at 150 20? for 60 seconds, immersed whole smd electrode in soldering bath at 240 5? for 3 1 seconds, then measured after resistance to exposure to room conditions for 2 hours. mil-std-202e soldering heat lead terminals are immersed up to 1.5mm from package base in soldering bath method 210a leaded at 260 5? for 10 1 seconds, then measured after exposure to room conditions for 2 hours. test item package test conditions test method dielectric withstanding both apply 100vdc between i/o terminals and ground terminal, for 1 minute. mil-std-202e voltage insulation resistance both apply 100vdc between i/o terminals and ground terminal, for 1 minute. mil-std-202e method 302 temperature smd filter shall be measured between ?0? to +60? temperature range. characteristics leaded filter shall be measured between ?0? to +50? temperature range. electrical 350 cg01-j saf series
|
